Recent Posts

Wednesday, 5 April 2017

  Autotransformer starter working, wiring and control diagram:

  There are various  starter used to start induction motor like Direct online starter, Soft starter,star delta starter,auto transformer starter,auto transformer starter is used for large HP motor.

Auto transformer control diagram :–

auto transformer motor starter control diagram
Fig:auto transformer motor starter control diagram
The operation principle of auto transformer method is similar to the star delta starter method. The starting current is limited by (using a three phase auto transformer) reduce the initial stator applied voltage.
 

The auto transformer starter is more expensive, more complicated in operation and bulkier in construction when compared with the star – delta starter method.

But an auto transformer starter is suitable for both star and delta connected motors, and the starting current and torque can be adjusted to a desired value by taking the correct
tapping from the auto transformer. 


When the star delta method is considered, voltage can be adjusted only by
factor of . 1/
3

An autotransformer starter reduces inrush current by using a transformer in the line just ahead of the motor to step down the voltage applied to the motor terminals.

By reducing the voltage, the current drawn from the line is reduced during start-up. When the setting time on the timer has expired, the auto transformer is bypassed.

The  auto transformer starter is a closed transition type, meaning that the motor remains connected to the line during the entire acceleration period. 

The transformer has three taps which provide 50%, 65% and 80% of full line voltage. 

At delivery the transformer is connected to the 65% tap the inrush current will be reduced to 42% of normal; and the starting torque will be reduced to 42%. 

The autotransformer starter can be used for any squirrel-cage motor.


Advantages Auto transformar starter:

1) The autotransformer starter limits significantly the inrush current. 

2) It is used for large motors, in which start by direct connection to the network is not possible. For large motors also the star-delta starter cannot be used, especially if they are started with a significant load.
 
3) The circuit has advantage over starting with a regular autotransformer, which needs to be at some point completely disconnected during the start inducing high voltage impulses,
which can damage the electrical insulation of the stator.
 
4)The most effective ratio of the autotransformer is between 65-80%.


Drawbacks Auto transformar motor starter:

1) The circuit is quite complex and involves relatively expensive autotransformer. 

2) Due to the physical size of the whole device it might not be possible to add the Korndorfer starter to an existing machine if space is scarce.

Saturday, 1 April 2017

why single-phase induction motor is not self-starting?

A single phase induction motor is very similar to a 3-phase squirrel cage induction motor
It has
(i)  a squirrel-cage rotor as to a 3-phase motor and
(ii)  a single-phase winding on the stator

Unlike a 3-phase induction motor,a single-phase induction motor is not self-starting but requires some starting means.
The single-phase stator winding produces a magnetic field that pulsates (alternate) in strength in a sinusoidal manner. but in case of 3 phase induction motor magnetic field rotating one
 The field polarity reverses after each half cycle but the field does not rotate.  Consequently,  the alternating flux cannot produce rotation in a stationary squirrel-cage rotor. However,  if the rotor of a single-phase motor is rotated in one direction by some mechanical means it will continue to run in the direction of rotation As a fact,  the rotor quickly accelerates until it reaches a speed slightly below the synchronous speed.once the motor is running at this speed,  it will continue to rotate even though single-phase current is flowing through the stator winding.

Making self-starting. 
To make a single-phase induction motor self-starting,  we should need to produce a revolving stator magnetic field This may be achieved by converting a single-phase supply into two phase supply through the use of an additional winding called starting winding employed perpendicular to main winding(90 degree apart) and it can be removed when motor attains sufficient speed, depending upon the type of the motor



Working principle of full wave bridge rectifier and digram

Full wave bridge rectifier - Rectifier is a circuit which convert alternating voltage into the direct voltage. There are three types o...

Popular Posts